Zairyo-to-Kankyo
New Arrival Alert : OFF

You can use this feature after you logged into the site.
Please click the button below.

Log in / Sign up
ONLINE ISSN: 1881-9664
PRINT ISSN: 0917-0480

Zairyo-to-Kankyo Vol. 55 (2006), No. 1

  • A Prospect from Mountain Moere

    pp. 1-1

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.55.1

    x

    Readers Who Read This Article Also Read

    1. How to Enjoy Research Life Zairyo-to-Kankyo Vol.55(2006), No.5
    2. Importance of Corrosion Prevention Technologies to Material Circulation Society Zairyo-to-Kankyo Vol.55(2006), No.4
    3. The Relationship Between CO2 Corrosion Resistance and Corrosion Products Structure on Carbon and Low Cr Bearing Steels Zairyo-to-Kankyo Vol.56(2007), No.11
  • Thermal Spray Coatings for Corrosion Prevention

    pp. 2-12

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.55.2

    Two types of thermal sprayed coatings for corrosion prevention in natural environments are discussed in this review. One is a sacrificial anode type coating of zinc and aluminum, which has a long history dating back to 1940's and will become more important as the expected service life of infrastructures become longer and the existing structures require good maintenance technology. The other is a dense barrier type coating of materials such as stainless steels and Ni-base alloys, which becomes more applicable due to the recent development of spray processes such as HVOF. Basic corrosion properties and field performances as well as problems to be solved of HVOF sprayed alloy coatings are discussed.
  • Failure Propensity of Austenitic Stainless Steels by Chloride Induced Stress Corrosion Cracking in Air

    pp. 20-24

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.55.20

    Chlorides induced stress corrosion cracking (ESCC) behavior was examined for SUS304L, SUS316L and SUS304 stainless steels (SS) after depositing synthetic sea water simulating sea salt particles at a temperature range from 333 K to 353 K with relative humidity of 35%. A stress-ESCC failure time relationship was formulated for SUS304L SS as σ=-Alog(tf)+B, where σ : applied stress (MPa), tf : time to failure (h), A=23.7T-7020, B=43.7T-11600, T : absolute temperature (K). Even an incipient micro-crack was not observed on the specimen surface of the SS at the applied stress level of 0.25σyy : 0.2% proof stress), although SCC initiated at the applied stress level of 0.5σy. Thus the threshold stress should be between 0.5σy and 0.25σy for these SS, and the threshold stress would rise beyond these values if the stress concentration be considered at the bottom and circumference of a pit. A statistical analysis suggested that the ESCC crack length and crack depth conformed to the double exponential distribution.
  • Mechanical Properties and Adhesion of Oxide Films Formed on Pure Titanium at High Temperature Corrosive Environments

    pp. 25-31

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.55.25

    The oxide films formed on metallic surfaces at high temperature corrosive environments often act as diffusive barriers of oxygen to protect the metal from corrosion. However, damage to metallic materials is possibly accelerated by mechanical fractures and spalling of the oxide films, caused by such as collisions of fly ash and thermal stresses of the oxide films. Investigations on mechanical properties and adhesion of oxide films formed on metal surfaces at high temperature corrosive environments lead to estimating the life time of materials and to searching high temperature corrosion prevention techniques. Both high temperature corrosion and round particle impact tests were performed on pure titanium coupon specimens. Both a particle impact method and an exfoliation/fracture model of oxide films were very useful to examine elastic modulus, fracture stresses and strains, and adhesive stresses of oxide films formed on pure titanium at high temperature environments. The spalling of the titanium oxide films was experimentally reproduced by the temperature decrement calculated by the elastic modulus and the adhesive stress obtained in this study, and by the thermal expansion coefficients of titanium and titanium oxide. These mechanical properties obtained in this study were, therefore, proved to be valid.

Article Access Ranking

26 Mar. (Last 30 Days)

  1. Dependence of Carbon Concentration and Alloying Elements on the Stability of Iron Carbides ISIJ International Advance Publication
  2. Comprehensive Optimization Control Technology of Rolling Energy and Oil Consumption in Double Cold Rolling ISIJ International Advance Publication
  3. Experiments on Removal of Hydrophilic Fine Particles in Bubbly Flow ISIJ International Vol.59(2019), No.2
  4. Effects of Impurities and Processing Conditions in Al–1%Mn Alloys on the Formation of Thermally Stabilized Substructures MATERIALS TRANSACTIONS Vol.59(2018), No.11
  5. Temperature Field Distribution of a Dissected Blast Furnace ISIJ International Advance Publication
  6. Coating Film Profiles Generated by Fluctuating Location of the Wiping Pressure and Shear Stress ISIJ International Vol.59(2019), No.2
  7. Effect of EAF Slag Temperature and Composition on its Electrical Conductivity ISIJ International Vol.59(2019), No.2
  8. Fundamentals of Silico-Ferrite of Calcium and Aluminium (SFCA) Iron Ore Sinter Bonding Phase Formation: Effects of Basicity and Magnesium on Crystallisation during Cooling ISIJ International Vol.59(2019), No.2
  9. Evolution of Blast Furnace Process toward Reductant Flexibility and Carbon Dioxide Mitigation in Steel Works ISIJ International Vol.56(2016), No.10
  10. Numerical Simulation of Multiphase Flow and Mixing Behavior in an Industrial Single Snorkel Refining Furnace (SSRF): The Effect of Gas Injection Position and Snorkel Diameter ISIJ International Advance Publication

Search Phrase Ranking

26 Mar. (Last 30 Days)

  1. blast furnace
  2. blast furnace productivity
  3. blast furnace permeability
  4. galvanizing
  5. tuyere abrasion
  6. tuyere erosion
  7. tuyere failure
  8. lme
  9. wear on tuyere
  10. 鉄と鋼