Zairyo-to-Kankyo
New Arrival Alert : OFF

You can use this feature after you logged into the site.
Please click the button below.

Log in / Sign up
ONLINE ISSN: 1881-9664
PRINT ISSN: 0917-0480

Zairyo-to-Kankyo Vol. 57 (2008), No. 5

  • Dreams of “Kocho” and “Kantan”

    pp. 209-210

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.57.209

    x

    Readers Who Read This Article Also Read

    1. How to Enjoy Research Life Zairyo-to-Kankyo Vol.55(2006), No.5
    2. 解説特集「腐食・防食技術コンサルタント」の企画にあたって Zairyo-to-Kankyo Vol.57(2008), No.10
    3. Importance of Corrosion Prevention Technologies to Material Circulation Society Zairyo-to-Kankyo Vol.55(2006), No.4
  • Technical Module of Erosion-corrosion

    pp. 211-217

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.57.211

    RBM (Risk Based Maintenance) is a promising method of maintenance for aged plants. The Risk is defined as the product of likelihood and consequence of failure. The likelihood of failure is evaluated by prediction of residual life or sensitivity of failure and degradation. Technical module is a tool to evaluate the likelihood of failure. In this paper development of technical module for erosion-corrosion which is one of the most likely mechanism of failure in aged plants is introduced.
  • A Consideration on Pipe-Wall Thinning Mechanisms from an Aspect of Fluid-Mechanics

    pp. 218-223

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.57.218

    The contribution of the fluid mechanics to the piping wall thinning phenomena was investigated. It was shown that the fluid force to the wall was quite different between flow accelerated corrosion (FAC) and erosion. The turbulent mass transfer, which is one of the primary factors of FAC, was analogous to the turbulent heat transfer. The model that the molecular transport in the viscous sublayer nearby soon of wall was predominant was practicable. In addition, the mass transport was predicted using commercial codes of computational fluid dynamics. Some prediction results of the mass transfer in orifice and the elbow using above techniques were explained.
  • Incubation Time of Stress Corrosion Cracking for Type 316L and Type 316 Stainless Steels by CBB Method in High Temperature Water

    pp. 230-234

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.57.230

    Incubation times of stress corrosion cracking (SCC) for mill annealed and cold rolled type 316L stainless steel (SS) and type 316 SS were examined by the creviced bent beam method in oxygenated high temperature water at 561 K. SCC was observed in type 316L SS after exposure of 1000 h to the test environment, although type 316 SS showed SCC susceptibility after exposure of 500 h. The fracture surface of both type 316L SS and type 316 SS consisted mainly of intergranular SCC with a small fraction of transgranular SCC similar to those observed in the actual components. The maximum SCC crack length [a] on the specimen surface increased in proportion to the logarithm of the exposure time [t] for each SS as ;
    a=700×ln(t)–4334 : type 316L SS,
    a=1078×ln(t)–6347 : type 316 SS.
    The incubation times of 490 h and 360 h were obtained for type 316L SS and type 316 SS, respectively, from the relationship between the crack length and the test time. The SCC incubation times were larger than that of sensitized type 304 SS by >3 times showing higher resistance to SCC of mill annealed, low carbon stainless steels.
  • Carbonation of Magnesium Hydroxide and Formation of Calcareous Deposit in Tidal Zone

    pp. 235-240

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.57.235

    The carbonation of Mg(OH)2 by carbon dioxide in air was examined. Compound, chemical composition, and surface property of the calcareous deposit formed in tidal zone were investigated.
    As a result of the carbonation of Mg(OH)2, dypingite was formed. Inside of the calcareous deposits composed of rust and Mg(OH)2 and dypingite. Outside of the calcareous deposits composed of aragonite and dypingite. Thus, it is considered dypingite in the calcareous deposit were formed from Mg(OH)2.

Article Access Ranking

19 May. (Last 30 Days)

  1. Influence of Thermomechanical Treatment on Delayed Fracture Property of Mo-Bearing Medium-Carbon Steel ISIJ International Vol.62(2022), No.2
  2. Interaction Coefficients of Mo, B, Ni, Ti and Nb with Sn in Molten Fe–18mass%Cr Alloy ISIJ International Vol.62(2022), No.3
  3. Dissolution Kinetics of Synthetic FeCr2O4 in CaO–MgO–Al2O3–SiO2 Slag ISIJ International Vol.62(2022), No.4
  4. Fundamentals of Silico-Ferrite of Calcium and Aluminium (SFCA) and SFCA-I Iron Ore Sinter Bonding Phase Formation: Effects of MgO Source on Phase Formation during Heating ISIJ International Vol.62(2022), No.4
  5. Surface Quality Evaluation of Heavy and Medium Plate Using an Analytic Hierarchy Process Based on Defects Online Detection ISIJ International Advance Publication
  6. Exploration of the Relationship between the Electromagnetic Field and the Hydrodynamic Phenomenon in a Channel Type Induction Heating Tundish Using a Validated Model ISIJ International Vol.62(2022), No.4
  7. Comparison of Oxidation Behavior of Various Reactive Elements in Alloys during Electroslag Remelting (ESR) Process: An Overview ISIJ International Advance Publication
  8. Assessment of Blast Furnace Operational Constraints in the Presence of Hydrogen Injection ISIJ International Advance Publication
  9. Phenomenological Understanding about Melting Temperature of Multi-Component Oxides Tetsu-to-Hagané Vol.108(2022), No.4
  10. Influence of Stabilizing Elements on Ductile-Brittle Transition Temperature (DBTT) of 18Cr Ferritic Stainless Steels ISIJ International Vol.62(2022), No.4

Search Phrase Ranking

19 May. (Last 30 Days)

  1. blast furnace
  2. blast furnace productivity
  3. blast furnace permeability
  4. steel
  5. galvannealing
  6. jet impingement
  7. jet impingement + cooling + runout table
  8. nitrogen
  9. refractory
  10. valve spring steel