Zairyo-to-Kankyo
New Arrival Alert : OFF

You can use this feature after you logged into the site.
Please click the button below.

Log in / Sign up
ONLINE ISSN: 1881-9664
PRINT ISSN: 0917-0480

Zairyo-to-Kankyo Vol. 60 (2011), No. 8

  • View of Material Application in the New Industry and Subject

    pp. 353-353

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.60.353

  • Potential Dependence of Preferential Dissolution Behavior of a Duplex Stainless Steel in Simulated Solution inside Crevice

    pp. 363-367

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.60.363

    Relationship between preferential dissolution behavior and the holding potential and its duration of the potentiostatic test of a duplex stainless steel in simulated solution inside corroding crevice was investigated. In the active region (−370, −300 and −260 mV vs. SCE), the current density decreased towards a certain value after the measurement started, then it stayed rather constant value until the end of the measurement, i.e., for 24 h. In the passive region (−200 and −150 mV), it decreased greatly towards certain values after the measurement started, then it stayed lower value until the end of the measurement. In all potential regions, current density values determined by potentiostatic tests showed about one order of magnitude lower than those of the dynamic anodic polarization curves. At the less noble potential (−370 mV) of the active region, ferritic phase preferentially dissolved, while that of noble (−260 mV) of the active region, the austenitic phase dissolved preferentially. In the passive region, both phases dissolved evenly. These dissolution behavior were observed in the potentiostatic tests for 15 min as well as for 24 h. Chemical composition of dissolved metal ions after dissolution tests at certain potentials in the active region was also analyzed. Chemical composition of dissolved metal ions was almost same as chemical composition of a preferential dissolution phase of the specimen at each holding potential. It would appear that chemical composition of dissolved metal into crevice solution reflects to the preferential dissolution phase.
  • Estimate of Crevice Corrosion Resistance of Welds in Ni-based Corrosion Resistant Alloys by Measuring of Repassivation Potentials for Crevice Corrosion

    pp. 368-373

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.60.368

    Corrosion resistance to crevice corrosion attack of welds made with various Ni-Cr-Mo(-Ta) alloy fillers connected to Ni-based alloy plates in a hot concentrated NaCl solution was investigated using the technique of measuring repassivation potentials for crevice corrosion (ER,CREV). The ER,CREV of the test electrode with a weld could be regard as it of the weld. Under this condition it was made clear that the dendrite core where was the alloy element depleted region determined the corrosion resistance to crevice corrosion attack of the weld to be degraded it. ER,CREV of weld has linear relationship to Pitting Resistance Equivalent with tantalum (PRE(Ta)=[%Cr]+3.3([%Mo]+0.5 [%W])+7.7 [%Ta]) which is calculated from dendrite core composition. The line consistents with the relationship between ER,CREV of base metal and PRE(Ta) which is calculated from its chemical compotion. Under more severe conditions for crevice corrosion such as higher temperature, the ER,CREV of alloy 22 showed the same value with it of the weld made with the filler having the same composition of the base metal. It was suggested that the depnendance of the corrosion resistance to crevice corrosion attack of the weld changed into its average chemical composition from the dendrite core composition.
  • Development of Corrosion Rate Measuring Apparatus for Carbon Steel under Reducing Environment

    pp. 374-379

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.3323/jcorr.60.374

    In order to monitor the corrosion rate of carbon steel under deep under-ground environment which is depleted with oxygen, the corrosion rate measuring apparatus using the hydrogen permeation current was developed. Inner surface of the carbon steel monitor electrode made of beverage can was coated with Ni or Pd-Ni plating, which was used as the hydrogen detecting electrode. Corrosion rate which was estimated from hydrogen permeation current well consisted with literature data. Corrosion rate in acidic solution at pH < 3.5 was found to be not changed with time, but the corrosion current in neutral and alkaline solution was decreased with time according to the parabolic rate law and approached the value below 0.01 μA/cm2 after long time elapsed.

Article Access Ranking

14 Apr. (Last 30 Days)

  1. Three-dimensional Investigations of Non-metallic Inclusions in Stainless Steels before and after Machining ISIJ International Advance Publication
  2. Perspective toward Long-term Global Goal for Carbon Dioxide Mitigation in Steel Industry Tetsu-to-Hagané Vol.105(2019), No.6
  3. Influence of Ore Assimilation and Pore Formation during Sintering on Reduction Behavior of Sintered Ores Tetsu-to-Hagané Vol.107(2021), No.3
  4. Numerical Simulation of Flow, Heat, Solidification, Solute Transfer and Electromagnetic Field for Vertical Mold and Curved Mold of Billet ISIJ International Vol.61(2021), No.3
  5. Deformation Behavior of Longitudinal Surface Flaws in Flat Rolling of Steel Wire ISIJ International Advance Publication
  6. Structural and Mechanical Characterizations of Top Dross in a Molten Zinc Bath ISIJ International Vol.61(2021), No.3
  7. Dissolution Behavior of Mg and Ca from Dolomite Refractory into Al-killed Molten Steel ISIJ International Advance Publication
  8. Numerical Study into Gravity Separation of Phosphorus from BOS Slag during Solidification ISIJ International Vol.61(2021), No.3
  9. Prediction of Spatial Composition Distribution of Inclusions in the Continuous Casting Bloom of a Bearing Steel under Unsteady Casting ISIJ International Vol.61(2021), No.3
  10. Improvement in Reduction Behavior of Sintered Ores in a Blast Furnace through Injection of Reformed Coke Oven Gas Tetsu-to-Hagané Vol.107(2021), No.4

Search Phrase Ranking

14 Apr. (Last 30 Days)

  1. blast furnace
  2. coke oven gas injection
  3. slag
  4. tetsu-to-hagané
  5. blast furnace productivity
  6. continuous casting of electrical steel
  7. electrical steel and continuous casting
  8. fundamental study on rapid reduction of chromium ore in basic oxygen furnace
  9. iron phosphide (fe2p, fe3p)
  10. iron phosphide (fe2p, fe3p), formation energy