ヘルプ

詳細検索

論文検索サイト

トップ
鉄と鋼
Vol. 75 (1989), No. 11

鉄と鋼 Vol. 75 (1989), No. 11

Grid List Abstracts

オンライン版ISSN:	1883-2954
冊子版ISSN:	0021-1575
発行機関:	The Iron and Steel Institute of Japan

Backnumber

Vol. 110 (2024)
1. No.15
2. No.14
3. No.13
4. No.12
5. No.11
6. No.10
7. No.9
8. No.8
9. No.7
10. No.6
11. No.5
12. No.4
13. No.3
14. No.2
15. No.1
Vol. 109 (2023)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 108 (2022)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 107 (2021)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 106 (2020)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 105 (2019)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 104 (2018)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 103 (2017)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 102 (2016)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 101 (2015)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 100 (2014)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 99 (2013)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 98 (2012)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 97 (2011)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 96 (2010)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 95 (2009)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 94 (2008)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 93 (2007)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 92 (2006)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 91 (2005)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 90 (2004)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 89 (2003)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 88 (2002)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 87 (2001)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 86 (2000)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 85 (1999)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 84 (1998)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 83 (1997)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 82 (1996)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 81 (1995)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 80 (1994)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 79 (1993)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 78 (1992)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 77 (1991)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 76 (1990)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 75 (1989)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 74 (1988)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 73 (1987)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 72 (1986)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 71 (1985)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 70 (1984)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 69 (1983)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 68 (1982)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 67 (1981)
1. No.16
2. No.15
3. No.14
4. No.13
5. No.12
6. No.11
7. No.10
8. No.9
9. No.8
10. No.7
11. No.6
12. No.5
13. No.4
14. No.3
15. No.2
16. No.1
Vol. 66 (1980)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 65 (1979)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 64 (1978)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 63 (1977)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 62 (1976)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 61 (1975)
1. No.15
2. No.14
3. No.13
4. No.12
5. No.11
6. No.10
7. No.9
8. No.8
9. No.7
10. No.6
11. No.5
12. No.4
13. No.3
14. No.2
15. No.1
Vol. 60 (1974)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 59 (1973)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 58 (1972)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 57 (1971)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 56 (1970)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 55 (1969)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 54 (1968)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 53 (1967)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 52 (1966)
1. No.13
2. No.12
3. No.11
4. No.10
5. No.9
6. No.8
7. No.7
8. No.6
9. No.5
10. No.4
11. No.3
12. No.2
13. No.1
Vol. 51 (1965)
1. No.13
2. No.12
3. No.11
4. No.10
5. No.9
6. No.8
7. No.7
8. No.6
9. No.5
10. No.4
11. No.3
12. No.2
13. No.1
Vol. 50 (1964)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 49 (1963)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 48 (1962)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 47 (1961)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 46 (1960)
1. No.14
2. No.13
3. No.12
4. No.11
5. No.10
6. No.9
7. No.8-supl
8. No.7
9. No.6
10. No.5
11. No.4
12. No.3
13. No.2
14. No.1
Vol. 45 (1959)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 44 (1958)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 43 (1957)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 42 (1956)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1
Vol. 41 (1955)
1. No.12
2. No.11
3. No.10
4. No.9
5. No.8
6. No.7
7. No.6
8. No.5
9. No.4
10. No.3
11. No.2
12. No.1

キーワードランキング

21 Nov. (Last 30 Days)

鉄と鋼 Vol. 75 (1989), No. 11

The Current Trend of Iron Ore and Coal Resources and the Future Prospect of Ironmaking Division

Nobuji NOSAKA, Yohzoh HOSOTANI

pp. 1957-1963

他の人はこちらも検索

Recent Progress in Iron Ore Sintering

鉄と鋼 Vol.68(1982), No.15

Effects of Oxygen Pressure, Al₂O₃ and MgO on the Liquidus Surface of FeO_x-SiO₂-CaO System

鉄と鋼 Vol.86(2000), No.7

Effect of Mineralogical Properties of Iron Ore on Its Assimilation with Lime

鉄と鋼 Vol.78(1992), No.7

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

A View of Emission Spectrometry

Kichinosuke HIROKAWA

pp. 1964-1968

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Recent Development of Life Evaluation of Reactor Pressure Vessels

Tadao IWADATE

pp. 1969-1980

他の人はこちらも検索

Relationship between Creep Strength and γ' Size in a Directionally Solidified Nickel-base Superalloy

鉄と鋼 Vol.73(1987), No.2

Improved 12Cr Rotor Forging for Ultra-Super-Critical Steam Turbine

鉄と鋼 Vol.76(1990), No.7

Recent Contributions of Work and Tool Materials for Cold Forged Products

鉄と鋼 Vol.76(1990), No.5

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Computational Fluid Dynamics

Tetuya KAWAMURA, Hideo TAKAMI

pp. 1981-1990

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Corrosion Behavior of Metallic Materials in Liquid Metals

Tadashi SUZUKI

pp. 1991-2002

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Development of Secondary Batteries Using Hydrogen Storage Alloys

Hiroshi ISHIKAWA, Tetsuo SAKAI

pp. 2003-2009

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Improvement in Retardation of Reduction and Melting-down Properties of Pellets

Ichiro SHIGAKI, Shouji SHIROUCHI, Kunihiko TOKUTAKE, Nobuhiro HASEGAWA

pp. 2010-2017

抄録

The high temperature properties of pellets and sinter such as retardation of reduction, carburization and melting-down in packed beds were studied with quenching method. The results obtained are summarized as follows ;
(1) Retardation of reduction of pellets is attributed to disappearance of micro pores caused by sintering of iron under the presence of a liquid exuded from wustite core.
(2) Carburization proceeds mainly through diffusion of carbon from surface of iron, grown by melting reduction, directly contacted with solid carbon.
(3) Retardation of reduction of pellets was improved by the adjustment of chemical composition of core part having high solidus temperature and melting-down property was ameliorated by increasing basicity of a whole pellet.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

The Effect of Second Order Interaction Parameters on the Solubility Product of Calcium and Oxygen in Molten Iron

Takashi WAKASUGI, Fumitaka TSUKIHASHI, Nobuo SANO

pp. 2018-2022

抄録

The equilibrium relationship of the Fe-Ca-O system was discussed in terms of Gibbs free energy changes and interaction parameters to explain the difference between the thermodynamically calculated solubility product of CaO in molten iron and the measured one. It was found that the strong affinity between calcium and oxygen accounts for the difference while there is some uncertainty for the free energy change of solution of calcium into iron. Second order interaction parameters have to be introduced for consistent description of the equilibrium of the Fe-Ca-O system although the contents of calcium and oxygen are very low.

他の人はこちらも検索

Effect of Surface Active Element on the Initial Solidification Structure of Stainless Steel Ingot

鉄と鋼 Vol.75(1989), No.8

Computer Control of Electric Arc Furnace Steelmaking Process Based on a Mathematical Model

鉄と鋼 Vol.74(1988), No.11

Activity Measurement of the Constituents in Fe_tO-MnO Slag Equilibrated with Iron

鉄と鋼 Vol.77(1991), No.9

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Standard Free Energies of Formation of CaO-Al₂O₃ Intermediate Compounds by Means of EMF Measurement of Galvanic Cells

Kazuhiro NAGATA, Jun TANABE, Kazuhiro S. GOTO

pp. 2023-2030

抄録

The standard free energies of formation of CaO-Al₂O₃ intermediate compounds formed of CaO and Al₂O₃ have been measured by means of Galvanic cells using 4CaO·P₂O₅ solid electrolyte. The following results were obtained ;
CaO·6Al₂O₃ : ΔG°f =- 16380-37.58 T (± 1 730) (1 3731 873K)
CaO·2Al₂O₃ :ΔG°f =- 15 650- 25.82 T (± 900) (1 3731 873K)
CaO·Al₂O₃ :ΔG°f = - 17 910-17.38 T (± 790) (1 3731 843K)
3CaO·Al₂O₃ : ΔG°f = - 11 790-28.27 T (± 1 190) (1 3731 635K)
The unit is J/mol. The activity of CaO in liquid slag in equibrium with solid CaO·Al₂O₃ was 0.248 at 1 773K and that in equibrium with solid 3CaO·Al₂O₃ was 0.619. The standard state of CaO is pure solid.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Melting Process of a Rectangular Ice Prism Immersed in Bubbling Jet in a Cylindrical Vessel

Manabu IGUCHI, Hiroaki TAKEUCHI, Hirotoshi KAWABATA, Tomomasa UEMURA, Zen-ichiro MORITA

pp. 2031-2037

抄録

Very high turbulent fluctuation inherent in bubbling jet suppresses the separation of boundary layer developing on the surface of a body immersed in the jet and makes fluids in the bulk layer contact with it from all directions. Therefore, as the turbulence increases, the local heat transfer coefficient around the body is supposed to have almost the same value all over the surface and become independent of the shape of the body. This was found to be true from the facts that a rectangular ice prism melted away while keeping the similar profiles and that the local heat transfer coefficient was well approximated by the mean heat transfer coefficient of a sphere. On the basis of this result, the complete melting time of a rectangular prism was estimated by using the mean heat transfer coefficient of a sphere. The result agreed well with the experimental one. This agreement implies that the present estimation method would be applied to various non-spherical bodies immersed in bubbling jet

他の人はこちらも検索

Effects of Pressure and Inert Gas Top Blowing on the Rate of Molten Steel Hydrogen Desorption

鉄と鋼 Vol.88(2002), No.5

粒子浮上を伴う円筒容器内旋回気泡噴流の基本特性

鉄と鋼 Vol.95(2009), No.6

日本鉄鋼協会第113回講演大会講演概要集(II) その2

鉄と鋼 Vol.73(1987), No.5

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Spray Nozzles for Spray Solidification of Molten Metals

Shigeta HARA, Norihito IKEMIYA, Kazumi OGINO

pp. 2038-2044

抄録

Two types of nozzles were made for spray solidification of molten metals : Type A in which nitrogen gas for spray formation is supplied through a small annular gap, and Type B where it is supplied through four small tubes set coaxially. Spray tests for water, molten Pb and Bi showed that the later (Type B) is superior to the former (Type A) in regard to the mass distribution of metal droplets in the spray zone and blocking-up of the gas delivery nozzle by the molten metal droplets. Metallographic observation of solidified samples obtained by using Type B nozzle, suggests that in the spray solidification process, heat extraction from metal droplets mainly occurs during the spray formation by metal-gas mixing and splat formation on a metal substrate.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Influence of Mn on Solubility of C and Snoek Peak in Low Carbon Steels

Hajime SAITOH, Kohsaku USHIODA

pp. 2045-2050

抄録

The influence of Mn on the solubility of C in ferrite equilibrium with cementite was investigated in low carbon steels containing Mn ranging from 0 to 1 mass % over a temperature range from 573 to 973 K. Internal friction method was employed together with chemical analysis of C by means of infrared absorption method after combustion.
It has been clarified that Mn hardly changes the solubility of C in ferrite in equilibrium with cementite (0.018 mass% at 973 K), whereas Mn reduces Snoek peak height despite the fact that the amount of C in solid solution is constant.
The proportionality constant K in the equation sol. C (ppm) = K × Q^-1_max(10^-4) was experimentally determined as a function of Mn content. K increases with increasing Mn content, which is caused by the lattice strain introduced by Mn atom and/or the chemical interaction between Mn and C atoms.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Contribution of Mn-C Complex to Electrical Resistivity and Influence of Mn on Solubility of C in Ferrite of Low-carbon Steels

YiWang SONG, Junji KIHARA, Kohsaku USHIODA

pp. 2051-2058

抄録

The contribution of Mn-C complex to the electrical resistivity and the influence of Mn on the solubility of carbon in ferrite in low-carbon steels were studied by electrical resistivity measurement together with internal friction measurement and chemical analysis. The variation of electrical resistivity and the deviation from Matthiessen's rule during quench-ageing were analyzed with the assumption that the decomposition of Mn-C complex and the carbide precipitation take place simultaneously during quench-ageing. The contribution of Mn-C complex to the electrical resistivity at 77 K ( α_d) was determined to be 5.6 × 10 ^-6 Ω·m/mol with the assumption that only single atoms of solute C(C^S) contribute to Snoek peak. Those of single C atoms (α_C) and Mn atoms (α_Mn) were determined to be 4.9 × 10 ^{- 6} and 3.0 × 10 ^-6 Ω·m/mol, respectivly. α_d is larger than α_C, but smaller than (α_C + α_Mn). This result is reasonable from physical point of view. If the solubility of C is defined as C^s+ C^d (C^d : C in the Mn-C complex), it hardly varies with the Mn concentration and is 0.017 mass% at 973 K over a range of the Mn concentration from 0 to 1.2 mass%.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

An Investigation about the Mechanism of Work Roll Wear at the Cold Rolling

Shuichi IWADOH, Hiroshi KUWAMOTO, Sakae SONODA

pp. 2059-2066

抄録

Through an experimental simulation using a large scale Timken tester, the mechanism of work roll wear in cold rolling was studied.
The problem of short work roll service life in the cold rolling of aluminum-killed continuous casted (Al-killed CC) steel sheet seems to be caused by fast reduction of surface roughness. The roughness reduction rate can be affected by iron soaps which are formed by the chemical reaction between free fatty acids (F. F. A.) contained in the rolling oil and steel strip. Iron soaps can act to thicken the oil film in the roll bite by increasing the viscosity of the rolling oil, and accelerate the roughness reduction. Additionally, iron soaps are used to create a strong oilness improving effect, so they prevent the metal contact between roll and strip asperities, and restrain the roughnes re-creation by scoring.
In the case of Al-killed CC steel rolling, because of its increased chemical activity with FFA, more iron soaps can be formed compared with capped steel, so the work roll service life can be shortened.

他の人はこちらも検索

Erosion of Ceramic Particle Composite Products for Pipe Transportation

鉄と鋼 Vol.75(1989), No.9

Multi-layer Coatings for Preventing Diffusion of Nickel into Tungsten Fiber

鉄と鋼 Vol.75(1989), No.9

Effect of Annealing Temperature on the Mechanical Properties of an Extra-low Carbon Cold-rolled Steel Sheet Containing P and Ti

鉄と鋼 Vol.75(1989), No.12

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Compressive Flow Stress Characteristics of Carbon Steels and Stainless Steels during Cold Forging

Kazunari SHINAGAWA, Takashi ISHIKAWA, Yuzo HOSOI

pp. 2067-2074

抄録

Flow stress-strain curves of material are necessary in numerical analysis, such as finite element analysis, of cold forging process. The behaviors of compressive flow stress-strain in carbon steels and stainless steels at various temperature in the range of cold forming are studied by static and dynamic upsetting tests. In the experiments, the stress-strain of feritic stainless steel shows similar curves with that of carbon steel in the temperature range from 30 to 200°C. Work-hardening behavior of austenitic stainless steel is more significantly affected by deformation temperature than those of carbon and feritic stainless. From the results of experiments, the flow stress is formularized as a function of strain, strain rate and temperature. The validity of this equation is examined through the comparison between load measured in upsetting test and that obtained by numerical simulation.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Determination of Fe²⁺ and Fe³⁺ Ratio in Iron Plating Bath by Measurement of Oxidation-Reduction Potential

Shigeo MATSUBARA, Yukimi MIWA, Kazuhiro TAKAGI, Yukihiro SHIRATAKI, Akinobu TAKEZOE, Takashi OMI

pp. 2075-2082

抄録

A trial has been conducted to apply Oxidation-Reduction Potential (ORP) to the on-line monitoring of Fe²⁺ and Fe³⁺ in a chloride bath for iron plating having iron concentration of 160230 g/l and Fe³⁺/Fe²⁺ concentration ratio of 0.01 0.12.From the analysis of ORP's at different bath pH (0.51.4), temperature (2095°) and flow rate (0200 cm/s), it was found that the concentration ratio Fe³⁺/Fe²⁺ in the plating bath can be directly obtained by measurements of ORP and bath temperature. Also, the precision of this method was satisfactory.
The present ORP method does not need such operations of chemical analysis as dilution and cooling of the sample solution, and addition of chemical reagents which contaminates the bath. Thus, it is concluded that Fe³⁺/Fe²⁺ ratio can be determined easily and continuously by simple procedure and apparatus.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Measurement of Paint Film Thickness on Prepainted Steel Sheet by Compton Scattered X-ray

Takanori AKIYOSHI, Toshiichi IWATA, Chikara TAKEUCHI

pp. 2083-2089

抄録

A new method for rapid meaurement of paint film thickness on prepainted steel was developed. In the developed method, intensities of Compton scattered X-ray from samples were measured as a indicator of paint film thickness by X-ray fluorescence spectrometer and RhK_α from X-ray tube was used for the incident X-ray. It was confirmed by experiment that intensities of Compton scattered X-ray from bulk samples were proportional to the reciprocal of absorption coefficients of X-ray in bulk. Intensities of Compton scattered X-ray from prepainted steel sheets were influenced by chemical composition of paints and amounts of Zn coating on steel sheets, and these influences were corrected by XRF intensities of individual elements measured simultaneously with Compton sacttered X-ray intensitity. Informations on samples such as densities of paints and amounts of Zn coating gave more accurate results. The reproducibility of values by the developed method was 0.15μm and the accuracy (variance of differences between data by the developed method and data by gravimetry) was 0.8 μm.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Effect of Sheet Surface Roughness on Clarity of Painted Sheet Steel

Kouzou TSUNOYAMA, Makoto IMANAKA, Kusuo FURUKAWA, Akira KISHIDA, Yasuhiro YAMADA

pp. 2090-2097

抄録

The influence of base metal surface roughness parameters on the clarity of painted automotive cold rolled sheet steels was investigated. The sheet steels were dull finished by shot blasting, electro-discharge texturing or laser dull texturing. It was found that the painted clarity improved with decreasing of Ra, while it scarcely depended on PPI. Characteristic of the surface profiles of base metal was the waviness with wavelength of hundreds micron. Whose trace remained after coating and deteriorated the clarity. In shot blasting, the dendritic microstructure and the statistical fluctuation of grit collision generated the waviness and made it difficult to control its wavelength. And, in electro-discharge texturing, it is suggested, controlling the waviness is difficult similarly. In laser dull texturing, it was possible to reduce the wavelength of waviness to less than hundreds micron and then to improve the clarity without deteriorating the press formability. A larger fraction of flat portion in laser dull texture was also responsible for the improvement of clarity.

他の人はこちらも検索

Effect of Surface Texture of Galvannealed Steel Sheet on Image Clarity after Painting

鉄と鋼 Vol.89(2003), No.1

Production and Technology of Iron and Steel in Japan during 2000

ISIJ International Vol.41(2001), No.7

State of the Art in Precoated Steel Sheet for Automotive Body Materials in Japan

ISIJ International Vol.31(1991), No.1

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Mechanisms for Evolution of Bubble in Porcelain Enamels

Tadayoshi WADA, Masakazu OSHIMI, Shunsuke GOTO

pp. 2098-2105

抄録

To clarify the bubble evolution during firing of one coat porcelain enamels on cold rolled Ti bearing steel sheets produced by continuous casting, analysis of gas chromatography and mass spectrometer of gas collected from the enamel on three kinds of enamelling steel sheets were analysed, and microstructures of both pickled specimens and fired ones were examined precisely. It was found that gases of one coat enamelling on Ti bearing steel sheet consisted of about 53% of hydrogen and 46% of nitrogen. The results show that hydrogen is thought to evolve from the water-iron reaction during firing, and nitrogen is thought to come from the air trapped in etched dent of grain boundary on steel sheet surface and between frit particles.
On the other hand, gases of capped steel sheet and less-Al-high-oxygen steel sheet produced by continuous casting consisted of 10% nitrogen and 90% of hydrogen which is thought to evolve from the same reaction as before.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

Effect of α/γ Phase Ratio and N Addition on the Corrosion Resistance of Si-bearing Duplex Stainless Steel in Nitric Acid

Haruhiko KAJIMURA, Kazuhiro OGAWA, Hiroo NAGANO

pp. 2106-2113

抄録

Duplex stainless steel is widely used in various service conditions due to its high mechanical properties and high corrosion resistance. However, the corrosion resistance of the duplex stainless steel in highly oxidizing nitric acid has not been made clear yet. In this study, the effect of Si content ( Si = 04%), γ phase ratio ( γ=2100%) and N addition (N=0.1%) on the corrosion resistance of 23 25Cr duplex stainless steel in 8N HNO₃ + 0.2 g/1Cr⁶⁺ boiling solution were investigated with TIG welded joint specimen. An intergranular corrosion depth and corrosion rate were measured after the corrosion test of 48 h×5 periods. And then a relationship between their microstructures and configuration of the corrosion attack was considered.
Si addition ( Si>3%) to the duplex stainless steels was effective to improve the corrosion resistance. The steel without N, however, was attacked at HAZ in case of γ<10% and γ>40%, because of α phase sensitization and σ phase formation, respectively.
N content affected α/γ ratio, nitride and carbide precipitation. As for the adequate ratio of α/γ for the resistance of intergranular corrosion of the duplex steel, obtained value experimentally was more than 50% in γ phase, in the case of 25Cr-Ni-4Si-N steel.

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

砂漠の地から見た日本(アレキサンドリア滞在記-2)

川上公成

pp. 2118-2121

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

Bibtex

Ris

論文アクセスランキング

21 Nov. (Last 30 Days)

In-situ Observation of Precipitation and Growth of MnS Inclusions during Solidification of a High Sulfur Steel

ISIJ International 早期公開
Measurement of Bubble Size Distribution and Generation Position of Bubbles Generated during Smelting Reduction of Iron Oxide-containing Slag

ISIJ International 早期公開
Injection of hydrogenous gases into the blast furnace tuyeres for reducing CO₂ emissions: a review

ISIJ International 早期公開
Development of a Low-carbon Sintering Process Technology and Its Application to a Pilot-scale Sintering Testing

ISIJ International Vol.64(2024), No.13
凝固過程における溶鋼中からAl₂O₃上へのMnSの晶出挙動

鉄と鋼早期公開
Molecular dynamics simulation of viscosity of the CaO, MgO and Al₂O₃ melts

ISIJ International 早期公開
Fe–(0.5–2.0)%Al–2.0%Mn合金の一方向凝固におけるAlNの晶出挙動に及ぼすAl濃度の影響

鉄と鋼早期公開
凝固過程のミクロ偏析による溶質濃度分布の定量的理解

鉄と鋼早期公開
SOKD: A soft optimization knowledge distillation scheme for surface defects identification of hot-rolled strip

ISIJ International 早期公開
Reduction and Carburization Behaviors of Iron Oxide Composite with Iron Carbide and Free Carbon

ISIJ International 早期公開

この機能はログイン後に利用できます。
下のボタンをクリックしてください。

鉄と鋼 Vol. 75 (1989), No. 11

キーワードランキング

reduction caco3 in electric furnace

kinetics of decarburization of liquid iron with high concentration ofcarbon

kinetics of decarburization of liquid iron by ar-coz gasmixture

ahss

charpy impact chemistry

dual phase steel

foamy slag in eaf

kinetics of decarburization of liquid iron by

ladle furnace flicker

scm440

鉄と鋼 Vol. 75 (1989), No. 11

The Current Trend of Iron Ore and Coal Resources and the Future Prospect of Ironmaking Division

SNSによる共有

A View of Emission Spectrometry

SNSによる共有

Recent Development of Life Evaluation of Reactor Pressure Vessels

SNSによる共有

Computational Fluid Dynamics

SNSによる共有

Corrosion Behavior of Metallic Materials in Liquid Metals

SNSによる共有

Development of Secondary Batteries Using Hydrogen Storage Alloys

SNSによる共有

Improvement in Retardation of Reduction and Melting-down Properties of Pellets

SNSによる共有

The Effect of Second Order Interaction Parameters on the Solubility Product of Calcium and Oxygen in Molten Iron

SNSによる共有

Standard Free Energies of Formation of CaO-Al2O3 Intermediate Compounds by Means of EMF Measurement of Galvanic Cells

SNSによる共有

Melting Process of a Rectangular Ice Prism Immersed in Bubbling Jet in a Cylindrical Vessel

SNSによる共有

Spray Nozzles for Spray Solidification of Molten Metals

SNSによる共有

Influence of Mn on Solubility of C and Snoek Peak in Low Carbon Steels

SNSによる共有

Contribution of Mn-C Complex to Electrical Resistivity and Influence of Mn on Solubility of C in Ferrite of Low-carbon Steels

SNSによる共有

An Investigation about the Mechanism of Work Roll Wear at the Cold Rolling

SNSによる共有

Compressive Flow Stress Characteristics of Carbon Steels and Stainless Steels during Cold Forging

SNSによる共有

Determination of Fe2+ and Fe3+ Ratio in Iron Plating Bath by Measurement of Oxidation-Reduction Potential

SNSによる共有

Measurement of Paint Film Thickness on Prepainted Steel Sheet by Compton Scattered X-ray

SNSによる共有

Effect of Sheet Surface Roughness on Clarity of Painted Sheet Steel

SNSによる共有

Mechanisms for Evolution of Bubble in Porcelain Enamels

SNSによる共有

Effect of α/γ Phase Ratio and N Addition on the Corrosion Resistance of Si-bearing Duplex Stainless Steel in Nitric Acid

SNSによる共有

砂漠の地から見た日本(アレキサンドリア滞在記-2)

SNSによる共有

論文アクセスランキング

In-situ Observation of Precipitation and Growth of MnS Inclusions during Solidification of a High Sulfur Steel

Measurement of Bubble Size Distribution and Generation Position of Bubbles Generated during Smelting Reduction of Iron Oxide-containing Slag

Injection of hydrogenous gases into the blast furnace tuyeres for reducing CO2 emissions: a review

Development of a Low-carbon Sintering Process Technology and Its Application to a Pilot-scale Sintering Testing

凝固過程における溶鋼中からAl2O3上へのMnSの晶出挙動

Molecular dynamics simulation of viscosity of the CaO, MgO and Al2O3 melts

Fe–(0.5–2.0)%Al–2.0%Mn合金の一方向凝固におけるAlNの晶出挙動に及ぼすAl濃度の影響

凝固過程のミクロ偏析による溶質濃度分布の定量的理解

SOKD: A soft optimization knowledge distillation scheme for surface defects identification of hot-rolled strip

Reduction and Carburization Behaviors of Iron Oxide Composite with Iron Carbide and Free Carbon

詳細検索

Standard Free Energies of Formation of CaO-Al₂O₃ Intermediate Compounds by Means of EMF Measurement of Galvanic Cells

Determination of Fe²⁺ and Fe³⁺ Ratio in Iron Plating Bath by Measurement of Oxidation-Reduction Potential

Injection of hydrogenous gases into the blast furnace tuyeres for reducing CO₂ emissions: a review

凝固過程における溶鋼中からAl₂O₃上へのMnSの晶出挙動

Molecular dynamics simulation of viscosity of the CaO, MgO and Al₂O₃ melts