logo
言語
ブックマーク
ログアウト

ジャーナル

論文検索サイト

アカウント

© 2022 Steel Science Portal

ヘルプ

詳細検索

論文検索サイト

site
site
site
site

鉄と鋼 Vol. 107 (2021), No. 9

ISIJ International
belloff

Grid List Abstracts
オンライン版ISSN: 1883-2954
冊子版ISSN: 0021-1575
発行機関: The Iron and Steel Institute of Japan

Backnumber

  1. Vol. 110 (2024)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  2. Vol. 109 (2023)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  3. Vol. 108 (2022)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  4. Vol. 107 (2021)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  5. Vol. 106 (2020)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  6. Vol. 105 (2019)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  7. Vol. 104 (2018)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  8. Vol. 103 (2017)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  9. Vol. 102 (2016)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  10. Vol. 101 (2015)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  11. Vol. 100 (2014)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  12. Vol. 99 (2013)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  13. Vol. 98 (2012)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  14. Vol. 97 (2011)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  15. Vol. 96 (2010)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  16. Vol. 95 (2009)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  17. Vol. 94 (2008)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  18. Vol. 93 (2007)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  19. Vol. 92 (2006)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  20. Vol. 91 (2005)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  21. Vol. 90 (2004)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  22. Vol. 89 (2003)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  23. Vol. 88 (2002)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  24. Vol. 87 (2001)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  25. Vol. 86 (2000)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  26. Vol. 85 (1999)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  27. Vol. 84 (1998)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  28. Vol. 83 (1997)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  29. Vol. 82 (1996)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  30. Vol. 81 (1995)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  31. Vol. 80 (1994)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  32. Vol. 79 (1993)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  33. Vol. 78 (1992)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  34. Vol. 77 (1991)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  35. Vol. 76 (1990)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  36. Vol. 75 (1989)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  37. Vol. 74 (1988)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  38. Vol. 73 (1987)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  39. Vol. 72 (1986)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  40. Vol. 71 (1985)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  41. Vol. 70 (1984)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  42. Vol. 69 (1983)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  43. Vol. 68 (1982)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  44. Vol. 67 (1981)

    1. No.16
    2. No.15
    3. No.14
    4. No.13
    5. No.12
    6. No.11
    7. No.10
    8. No.9
    9. No.8
    10. No.7
    11. No.6
    12. No.5
    13. No.4
    14. No.3
    15. No.2
    16. No.1

  45. Vol. 66 (1980)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  46. Vol. 65 (1979)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  47. Vol. 64 (1978)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  48. Vol. 63 (1977)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  49. Vol. 62 (1976)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  50. Vol. 61 (1975)

    1. No.15
    2. No.14
    3. No.13
    4. No.12
    5. No.11
    6. No.10
    7. No.9
    8. No.8
    9. No.7
    10. No.6
    11. No.5
    12. No.4
    13. No.3
    14. No.2
    15. No.1

  51. Vol. 60 (1974)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  52. Vol. 59 (1973)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  53. Vol. 58 (1972)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  54. Vol. 57 (1971)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  55. Vol. 56 (1970)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  56. Vol. 55 (1969)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  57. Vol. 54 (1968)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  58. Vol. 53 (1967)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  59. Vol. 52 (1966)

    1. No.13
    2. No.12
    3. No.11
    4. No.10
    5. No.9
    6. No.8
    7. No.7
    8. No.6
    9. No.5
    10. No.4
    11. No.3
    12. No.2
    13. No.1

  60. Vol. 51 (1965)

    1. No.13
    2. No.12
    3. No.11
    4. No.10
    5. No.9
    6. No.8
    7. No.7
    8. No.6
    9. No.5
    10. No.4
    11. No.3
    12. No.2
    13. No.1

  61. Vol. 50 (1964)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  62. Vol. 49 (1963)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  63. Vol. 48 (1962)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  64. Vol. 47 (1961)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  65. Vol. 46 (1960)

    1. No.14
    2. No.13
    3. No.12
    4. No.11
    5. No.10
    6. No.9
    7. No.8-supl
    8. No.7
    9. No.6
    10. No.5
    11. No.4
    12. No.3
    13. No.2
    14. No.1

  66. Vol. 45 (1959)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  67. Vol. 44 (1958)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  68. Vol. 43 (1957)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  69. Vol. 42 (1956)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

  70. Vol. 41 (1955)

    1. No.12
    2. No.11
    3. No.10
    4. No.9
    5. No.8
    6. No.7
    7. No.6
    8. No.5
    9. No.4
    10. No.3
    11. No.2
    12. No.1

キーワードランキング

03 Dec. (Last 30 Days)

鉄と鋼 Vol. 107 (2021), No. 9

製鋼スラグ高温還元による鉄源回収技術の開発

中瀬 憲治, 松井 章敏, 中井 由枝, 菊池 直樹, 岸本 康夫, 鉄山 一州

pp. 693-700

DOI:

10.2355/tetsutohagane.TETSU-2021-027

抄録

In order to develop a new recycling process of steelmaking slag, reduction of (FetO) and (P2O5) in steelmaking slag at high temperature has been investigated. In this work, 50 kg-scale experiments which simulated rotary kiln were conducted to investigate the separation behavior between slag and metal. Main results are as follows. (1) Molten iron was tapped out from the experimental furnace under the condition that more than 86% iron was reduced. (2) Weight of reduced iron did not affect the undefined ratio of phosphorus. (3) Common logarithm of phosphorus distribution ratio (logLP), which was used as an index to explain the effect of slag composition, temperature and oxygen potential, correlates to the undefined phosphorus ratio. (4) In the experiments which simulated rotary kiln treatment, calculated phosphorus distribution ratio (LP) was smaller than that from experimental results. It can be said that the phosphorus transfer into the metallic phase decreased because the smaller interface between slag phase and metallic phase was obtained due to the slag/metal separation.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

製鋼スラグ高温還元による鉄源回収技術の開発

twitter
facebook
mendeley

Bibtex

Ris

CaO非飽和の高濃度リン酸含有スラグにおける高温相平衡

内田 祐一, 渡邉 知穂, 長谷川 将克

pp. 701-711

DOI:

10.2355/tetsutohagane.TETSU-2021-046

抄録

Japan relies on imports for almost the entire amount of phosphorus, which is indispensable for human life and industrial materials. Therefore it is required to recover phosphorus from dephosphorization slag and sewage sludge which are promising unutilized phosphorus resources. Aiming wholesale recovery of phosphorus from the slag and sludge, a fundamental study on condensation of phosphorus in solid phase through high temperature phase separation was carried out. The experiments at 1573 K on principal [CaO-SiO2-P2O5] ternary model sample and Al2O3 and Fe2O3 added therein showed unsaturation with CaO and precipitation of solid 3CaO・P2O5 as the phosphorus-concentrated phase in all the sample. The contamination of the other components in 3CaO・P2O5 was low, especially less than 1 mass% for Al2O3 added samples. The liquid phase was also formed with Al2O3 or Fe2O3 addition, and the liquidus composition in quaternary samples were consistent with those appeared in [CaO-SiO2-Fe2O3] and [CaO-SiO2-Al2O3] ternary diagram. P2O5 content in the quaternary liquid phases were lower in Al2O3 added samples than those in Fe2O3 added samples. Such difference was discussed in terms of optical basicity and CaO activity for liquid phase. Due to the coexistence of solid SiO2 phase at Fe2O3 addition, the SiO2 content in liquid phase became lower compared to Al2O3 addition, and led to higher optical basicity, which would allow higher P2O5 capacity in liquid phase. These considerations strongly suggest that an effective control of composition would be key technology for the phosphorus recovery through condensation and separation of phosphorus concentrated phase.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

CaO非飽和の高濃度リン酸含有スラグにおける高温相平衡

twitter
facebook
mendeley

Bibtex

Ris

電位制御したKCl水溶液/Hgおよび溶融塩/Sn界面を通過する気泡の直接観察

小西 宏和, 小野 英樹

pp. 712-721

DOI:

10.2355/tetsutohagane.TETSU-2021-024

抄録

In-situ observation of Ar bubble through each interface of a KCl aqueous solution / Hg and a molten salt / liquid Sn were conducted by controlling applied potential in order to simulate the behavior of bubble at interface of slag / metal. In a KCl aqueous solution, the rate of Ar bubble through each interface of a KCl aqueous solution / Hg became slow with applying −2.0 V at 298 K. This behavior caused by the stabilization of interface with deceasing the interfacial tension, and a lot of Hg droplet formed by rupture of bubble was drawn into Hg phase under the interface in seconds. In a LiCl-KCl eutectic melt, the interfacial tension of the molten salt / liquid Sn were measured by the in-site observation of contact angle with applying −2.0~0 V(vs. Ag+/Ag) at 793 K. The behavior of interfacial tension corresponded to typical electrocapillary curve. The interfacial tension at −0.75 V became highest, 310 (dyn/cm = mN/m), and the interfacial tension at −2.0, 0 V became lowest, 210 (dyn/cm = mN/m), and the Ar bubble through the interface became slowest with applying at −2.0 V. This behavior was same as that through the interface of KCl aqueous solution / Hg.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

電位制御したKCl水溶液/Hgおよび溶融塩/Sn界面を通過する気泡の直接観察

twitter
facebook
mendeley

Bibtex

Ris

弱撹拌型上底吹き転炉のスラグ-メタル間反応速度に及ぼす炉体形状の影響

吉田 裕典, 天野 勝太, 中井 由枝, 髙橋 幸雄, 菊池 直樹

pp. 722-731

DOI:

10.2355/tetsutohagane.TETSU-2021-042

抄録

The peroxidation of molten steel is a problem occurred in a combined blowing converter with inert gas blowing. It caused by a relatively weak mixing power of bottom blown inert gas compared with that of bottom blown oxygen gas. In order to resolve the problem, several methods for optimizing top and bottom blowing conditions has developed. However, the effect of the equipment condition such as converter shape on the metallurgical characteristics has not been investigated enough. In this study, the effect of H/D (ratio of bath depth H to bath diameter D) on the reaction rate between slag and metal, and furnace body vibration in converter was investigated by water model experiments. It was found that the apparent reaction rate constant, kA/Vw, increase with increasing H/D, except for the case of H/D=0.85. It seemed that the change of kA/Vw with increasing H/D has a relation to the behavior of bath vibration. From the analysis based on the bath surface vibration model, it was indicated that the change of H/D affects the bath surface vibration behavior and the formation behavior of slag emulsion, and these effects increase the reaction interface between slag and metal.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

弱撹拌型上底吹き転炉のスラグ-メタル間反応速度に及ぼす炉体形状の影響

twitter
facebook
mendeley

Bibtex

Ris

冷間圧延用オンライン先進率モデルの開発

藤井 康之, 前田 恭志, 宇都宮 裕

pp. 732-740

DOI:

10.2355/tetsutohagane.TETSU-2021-022

抄録

Compared with the rolling conditions of mild steels, those of high tensile strength steels (HTSS) are very different, because of their high flow stress. Dimensional accuracy of the thickness at the top end of industrially rolled HTSS is lower, compared with mild steel. This is because predicted rolling force for HTSS is not accurate sufficiently. This problem is due to not only the used flow stress model, but also the rolling theory model. If the standard Hill’s rolling force equation and the standard Bland and Ford’s forward slip equation are used, a large discrepancy between the two estimated friction coefficients is observed in high slip region for HTSS. In this study, the authors propose new practical equations for the forward slip. The equation takes into account the effects of non-constant flow stress and of friction coefficient over the roll bite so that the equations are applicable to HTSS rolling conditions. The Bland and Ford’s equation has been modified to introduce 2 new parameters (C and B). Parameter C corresponds to the change of the friction coefficient in the roll bite, and parameter B corresponds to that of the flow stress. The new equations have been installed into an actual set-up model of steel works. Improvements in prediction accuracy of rolling force and forward slip are confirmed.

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

冷間圧延用オンライン先進率モデルの開発

twitter
facebook
mendeley

Bibtex

Ris

その場中性子回折実験によるSUS316L鋼の応力-ひずみ曲線におよぼす温度の影響

土田 紀之, 上路 林太郎, 井上 忠信

pp. 741-750

DOI:

10.2355/tetsutohagane.TETSU-2021-047

抄録

In situ neutron diffraction experiments during tensile deformation were conducted to investigate the effect of temperature on the tensile properties of JIS-SUS316L steel from the phase stresses of austenite (γ) and ferrite (α) phases and the kinetics of deformation-induced martensitic transformation (DIMT). The 0.2% proof stress and tensile strength increased with decreasing deformation temperature, and the maximum uniform elongation was reached at 223 K. The temperature of the maximum uniform elongation in metastable austenitic stainless steels is related to the mechanical stability of γ and showed good correlation with the Ni equivalent. The estimated phase stress of γ at a given true strain increased with decreasing temperature; however, the temperature dependence of the twinning-induced plasticity effect of the γ phase was small. The phase stress of α was almost independent of temperature between 138 K and 223 K. The effect of temperature on the mechanical properties of the SUS316L steel was largely affected by the transformation-induced plasticity effect, which was related to the kinetics of DIMT according to in situ neutron diffraction experiments.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

その場中性子回折実験によるSUS316L鋼の応力-ひずみ曲線におよぼす温度の影響

twitter
facebook
mendeley

Bibtex

Ris

準安定オーステナイト鋼のTRIP効果における加工誘起マルテンサイトの役割

土田 紀之, 石丸 詠一朗, 川 真知

pp. 751-759

DOI:

10.2355/tetsutohagane.TETSU-2021-054

抄録

Role of deformation-induced martensite in the transformation-induced plasticity (TRIP) of metastable austenitic steels was studied by examining effects of temperature on the tensile properties of Fe–18%Cr–6%Ni–0.2%N–0.1%C (6Ni–0.2N–0.1C) steel. The tensile properties obtained by tensile tests at various temperatures between 123 and 373 K were compared with those of SUS304 steel. The 0.2% proof stress, tensile strength, and uniform elongation of the 6Ni–0.2N–0.1C steel were larger than those of SUS304 at all temperature studied, and the mechanical stability of the austenite for the 6Ni–0.2N–0.1C steel was higher than that for the SUS304 steel. Neutron diffraction experiments at room temperature showed that the improvements in the mechanical properties in the 6Ni–0.2N–0.1C steel were associated with larger work hardening of the austenite and larger strength of the deformation-induced martensite. The increase in strength of deformation-induced martensite with N and C additions leads to better mechanical properties due to the TRIP effect, despite of smaller amounts of deformation-induced martensitic transformation.

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

準安定オーステナイト鋼のTRIP効果における加工誘起マルテンサイトの役割

twitter
facebook
mendeley

Bibtex

Ris

張出し成形した焼戻しマルテンサイト鋼板の水素脆化に及ぼす残留応力の影響

西村 隼杜, 北條 智彦, 味戸 沙耶, 柴山 由樹, 小山 元道, 齋藤 寛之, 城 鮎美, 安田 良, 菖蒲 敬久, 秋山 英二

pp. 760-768

DOI:

10.2355/tetsutohagane.TETSU-2021-055

抄録

The effects of residual stress on the hydrogen embrittlement behavior of a tempered martensitic steel sheet with 1-GPa-class tensile strength stretch-formed by a hemisphere punch simulating press-formed automotive structural parts were investigated. Cracking on the stretch-formed specimen induced by potentiostatic hydrogen charging was initiated in the foot of the impression of the specimen and propagated to the radial direction both toward the hillside and the plain. The mixture of quasi cleavage and intergranular fractures were observed whole through the fracture surface. Residual stress in the stretch-formed specimens was analyzed by using energy-dispersive X-ray diffraction method utilizing the synchrotron X-ray radiation at SPring-8. In addition, stress and plastic strain distributions in the specimen were analyzed by using Finite Element Method (FEM). These analyses depicted that the high tensile stress in the circumferential direction was in the foot of the impression, corresponding to the direction of the crack growth. The FEM analysis revealed that the high triaxial stress was in the foot suggesting accumulation of hydrogen. It was considered that the preferential crack initiation at the foot was promoted by the high residual stress in the circumferential direction and the hydrogen accumulation due to stress-induced diffusion.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

張出し成形した焼戻しマルテンサイト鋼板の水素脆化に及ぼす残留応力の影響

twitter
facebook
mendeley

Bibtex

Ris

和釘の錆の微細構造に及ぼす過飽和固溶酸素の影響

永田 和宏, 古主 泰子, 山下 孝子

pp. 769-779

DOI:

10.2355/tetsutohagane.TETSU-2021-014

抄録

The oxygen concentration in old Japanese nails was measured to be 0.15 mass% to 0.38 mass% by EPMA. These nails were one with bended top used for the main hall of the Anumi shrine in 1835, one with rolled top for the gate of the Saidai-ji temple in ca. 1300, one with rolled top for the eaves of the main hall of the Amanosan-kongo-ji temple in 1085~1124 and one with bended top in the five-storied pagoda of the Bicchu-Kokubun-ji temple before 800. At the measurement point of EPMA, no oxide with the size more than 10 nm was detected by HRTEM. Oxygen in iron base of the nails is in the state of supersaturated solid solution. Oxygen was absorbed in molten iron with white sparks, ‟Wakibana”, during the processes of Tatara smelting, decarburization in Okaji process and forge-and-welding, followed by rapid solidification of iron for oxygen to be supersaturated in solid solution. This is the common characteristics of pre-modern ironmaking process in the world. A thin layer of Fe3O4 was observed in the interface between FeO layer and iron base of nail, which was formed by the reaction of oxygen supersaturated in solid solution at the interface during forging. Most of inclusions in nails were FeO silicate slag with FeO fine particles. As there were FeS particles in silicate slag inclusions in the nail of the Bicchu-kokubun-ji temple, the nail was probably manufactured from iron produced using the mixture of iron sand and iron ore by Tatara smelting in the south of Okayama prefecture.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

和釘の錆の微細構造に及ぼす過飽和固溶酸素の影響

twitter
facebook
mendeley

Bibtex

Ris

冷間加工したフェライト鋼の強化挙動に及ぼす転位の性質と分布の影響

高木 節雄

pp. 780-783

DOI:

10.2355/tetsutohagane.TETSU-2021-052

抄録

Dislocation strengthening is affected by not only dislocation density but also character and dispersion of dislocations. In terms of the effect of dislocation dispersion, strengthening behavior can be explained by applying a dispersion coefficient; δ (= n / ρ) in theoretical dislocation strengthening equation, here n and ρ are the number of dislocation colonies on a slip plane and dislocation density respectively. Dislocation pinning spacing is given as a function of n –value, so that the increment of strength Δσ can be theoretically estimated using the dispersion coefficient δ. In cold rolled ferritic steel (Fe-0.0056%C), the comparison of theoretical values with experimental data proved δ≒0.21 in the dislocation density range above 1×1014/m2. In addition, experimental results indicated that the screw component of dislocations decreases with an increase of dislocation density. With respect to the ability of dislocation strengthening, edge dislocation is about 1.4 times larger than screw dislocation. As a result, a linear Bailey-Hirsch relationship; Δσ[GPa]≒1.8×10−8ρ is realized due to the changes of dislocation character with an increase of dislocation density.

他の人はこちらも検索

mendeley

ブックマーク

詳細

PDFダウンロード

SNSによる共有

論文タイトル

冷間加工したフェライト鋼の強化挙動に及ぼす転位の性質と分布の影響

twitter
facebook
mendeley

Bibtex

Ris

論文アクセスランキング

03 Dec. (Last 30 Days)

この機能はログイン後に利用できます。
下のボタンをクリックしてください。

詳細検索

論文タイトル

著者

抄録

ジャーナル名

年

出版日を西暦で入力してください（4桁の数字）。

検索したいキーワードを入力して下さい