論文検索サイト

鉄と鋼 Vol. 96 (2010), No. 2

ISIJ International
belloff

Grid List Abstracts

オンライン版ISSN: 1883-2954
冊子版ISSN: 0021-1575
発行機関: The Iron and Steel Institute of Japan

Backnumber

  1. Vol. 110 (2024)

  2. Vol. 109 (2023)

  3. Vol. 108 (2022)

  4. Vol. 107 (2021)

  5. Vol. 106 (2020)

  6. Vol. 105 (2019)

  7. Vol. 104 (2018)

  8. Vol. 103 (2017)

  9. Vol. 102 (2016)

  10. Vol. 101 (2015)

  11. Vol. 100 (2014)

  12. Vol. 99 (2013)

  13. Vol. 98 (2012)

  14. Vol. 97 (2011)

  15. Vol. 96 (2010)

  16. Vol. 95 (2009)

  17. Vol. 94 (2008)

  18. Vol. 93 (2007)

  19. Vol. 92 (2006)

  20. Vol. 91 (2005)

  21. Vol. 90 (2004)

  22. Vol. 89 (2003)

  23. Vol. 88 (2002)

  24. Vol. 87 (2001)

  25. Vol. 86 (2000)

  26. Vol. 85 (1999)

  27. Vol. 84 (1998)

  28. Vol. 83 (1997)

  29. Vol. 82 (1996)

  30. Vol. 81 (1995)

  31. Vol. 80 (1994)

  32. Vol. 79 (1993)

  33. Vol. 78 (1992)

  34. Vol. 77 (1991)

  35. Vol. 76 (1990)

  36. Vol. 75 (1989)

  37. Vol. 74 (1988)

  38. Vol. 73 (1987)

  39. Vol. 72 (1986)

  40. Vol. 71 (1985)

  41. Vol. 70 (1984)

  42. Vol. 69 (1983)

  43. Vol. 68 (1982)

  44. Vol. 67 (1981)

  45. Vol. 66 (1980)

  46. Vol. 65 (1979)

  47. Vol. 64 (1978)

  48. Vol. 63 (1977)

  49. Vol. 62 (1976)

  50. Vol. 61 (1975)

  51. Vol. 60 (1974)

  52. Vol. 59 (1973)

  53. Vol. 58 (1972)

  54. Vol. 57 (1971)

  55. Vol. 56 (1970)

  56. Vol. 55 (1969)

  57. Vol. 54 (1968)

  58. Vol. 53 (1967)

  59. Vol. 52 (1966)

  60. Vol. 51 (1965)

  61. Vol. 50 (1964)

  62. Vol. 49 (1963)

  63. Vol. 48 (1962)

  64. Vol. 47 (1961)

  65. Vol. 46 (1960)

  66. Vol. 45 (1959)

  67. Vol. 44 (1958)

  68. Vol. 43 (1957)

  69. Vol. 42 (1956)

  70. Vol. 41 (1955)

鉄と鋼 Vol. 96 (2010), No. 2

ガス吹込み精錬における機械攪拌を利用した気泡の微細化と分散強化

劉 燕, 佐野 正道, 張 廷安, 王 強, 赫 冀成

pp. 57-63

抄録

Water model experiments were performed for developing highly efficient gas injection refining processes. Mechanical stirring was applied to disintegrate the injected bubbles and to disperse them widely in the bath. The bubble disintegration and dispersion were investigated by changing rotation mode (direction of rotation), rotation speed and blade size of the impeller, and gas flow rate. Forward rotation of the impeller induced a stable tangential flow and could not disperse bubbles in the bath due to formation of a vortex around the impeller shaft. The tangential flow was suppressed by forward-interrupt rotation, which could reduce the vortex formation to some degree. However, the forward-interrupt rotation could not disperse the bubbles widely in the bath. Forward–reverse rotation could prevent the vortex formation completely and create a turbulent and strong shear stress field, which intensified the bubble disintegration and dispersion in the bath. Higher impeller rotation speed and larger blade length in the forward–reverse rotation could enhance the bubble disintegration more intensely, and make the dispersed bubbles smaller and the bubble dispersion zone wider. The bubble size tended to be larger at higher gas flow rates. However, its dependence on the gas flow rate became smaller at higher impeller rotation speed.

ブックマーク

SNSによる共有

論文タイトル

ガス吹込み精錬における機械攪拌を利用した気泡の微細化と分散強化

共焦点走査型レーザ顕微鏡と放射光を用いたX線回折による低炭素高合金鋼マルテンサイト変態過程のその場観察

張 朔源, 寺崎 秀紀, 小溝 裕一

pp. 64-69

抄録

Martensite transformation of Low carbon high alloy steel during cooling was in-situ observed by using high temperature laser scanning confocal microscopy and X-ray diffraction by Synchrotron radiation. The crystallography of martensite and retained austenite structure were analyzed by electron back scattered diffraction patterns (EBSD). From the test results it could be concluded that the austenite phase is stress- relieved by twin deformation when the martensite transformation is occurred.

ブックマーク

SNSによる共有

論文タイトル

共焦点走査型レーザ顕微鏡と放射光を用いたX線回折による低炭素高合金鋼マルテンサイト変態過程のその場観察

オーステナイト系ステンレス鋼の中性子小角散乱に及ぼす窒素添加と塑性変形の影響

池田 圭太, 小島 真由美, 友田 陽, 鈴木 淳市

pp. 70-75

抄録

The small angle neutron scattering (SANS) profile has been found to be influenced by nitrogen addition and plastic deformation for austenitic stainless steels. In solution-treated specimens, the slope of plots for SANS intensity versus the magnitude of scattering vector, q, becomes larger than −4 in the Porod region, suggesting the influence of short range N ordering. The change in scattering intensity profile with tensile deformation was in situ measured and it is found that SANS intensity becomes larger with increasing of plastic strain except a q region around 0.6 nm−1 for N bearing steel, where the intensity decreases in the beginning and then increases with increasing of plastic strain. This temporary decrease in SANS intensity is confirmed for cold rolled specimens. Severe deformation given by swaging to a N free steel brings larger increase in SANS intensity than a N bearing steel. The influence of plastic deformation on SANS intensity is larger in austenitic steels than in ferritic steels.

ブックマーク

SNSによる共有

論文タイトル

オーステナイト系ステンレス鋼の中性子小角散乱に及ぼす窒素添加と塑性変形の影響

室温高圧水素ガス環境下におけるSNCM439鋼の脆化現象

荒島 裕信, 政田 悟, 伊藤 秀明, 大西 敬三

pp. 76-83

抄録

The hydrogen environment embrittlement of SNCM439 steels (Ni–Cr–Mo steels) was investigated in 20-MPa hydrogen gas at room temperature at different tensile strengths ranging from 800 to 1200 MPa by heat treatments. The results of tensile tests revealed that hydrogen environment embrittlement was observed as decrease of ductility, whereas the tensile strength of the specimens did not change. Although the uniform elongation of the specimens was the same in air and hydrogen, local contraction decreased with increasing tensile strength in hydrogen. In contrast to the specimens with smooth surface, the notch tensile strength of the specimens having a tensile strength of over 1000 MPa remarkably decreased. The analysis of fractures in the specimens revealed that a crack was initiated from the external of the specimens in hydrogen, whereas it was initiated from the center of the specimens in air. The fracture mode was the same in both the tensile tests with notched and notchless specimens, and the presence of hydrogen induced quasi-cleavage fracture. It was observed that intergranular fracture was dominant in highly embrittled materials, and quasi-cleavage fracture was ahead of intergranular fracture. Even in the notched specimens whose intergranular fracture was dominant, quasi-cleavage fracture was observed beneath the notch. These behaviors indicate that the susceptibility to hydrogen embrittlement was more remarkable in specimens with high tensile strength, and the large plastic deformation required for the formation of quasi-cleavage fracture induced hydrogen penetration and hydrogen environment embrittlement.

ブックマーク

SNSによる共有

論文タイトル

室温高圧水素ガス環境下におけるSNCM439鋼の脆化現象

ベイニティックフェライト・マルテンサイト混合組織を母相とする超高強度低合金TRIP鋼板の伸びフランジ性

村田 宗央, 小林 純也, 杉本 公一

pp. 84-92

抄録

The microstructure, retained austenite characteristics, tensile properties and stretch-flangeability of ultra high-strength 0.2%C–1.5%Si–1.5%Mn (mass%) TRIP-aided bainitic ferrite cold-rolled sheet steel, “TBF steel”, were investigated for automotive applications. When isothermally held at temperatures less than martensite-start temperature for 300–3000 s after annealing or austenitizing, the TBF steel possessed mixed matrix structure of bainitic ferrite and martensite, with retained austenite of about 4 vol%. The TBF steel achieved the tensile strength higher than 1400 MPa and hole-expanding ratio of 40%. The good combination of tensile strength and hole-expanding ratio was mainly caused by highly carbon–enriched retained austenite and softened matrix structure composing of bainitic ferrite and martensite.

ブックマーク

SNSによる共有

論文タイトル

ベイニティックフェライト・マルテンサイト混合組織を母相とする超高強度低合金TRIP鋼板の伸びフランジ性

生体用Ti–Nb–Ta–Zr–O系合金のミクロ組織と力学的機能性に及ぼすニオブおよび酸素量の影響

赤堀 俊和, 新家 光雄, 小野 智之, 仲井 正昭, 堤 晴美

pp. 93-100

抄録

Ti–30Nb–10Ta–5Zr–0.3O (TNTZO) alloy, which is simplified chemical composition similar to that of biomedical Ti–29Nb–13Ta–4.6Zr alloy, and the same system alloys of TNTZO with different oxygen (O) and niobium (Nb) contents such as Ti–30Nb–10Ta–5Zr–0.5O, Ti–30Nb–10Ta–5Zr–0.6O alloys, and Ti–27Nb–10Ta–5Zr–0.3O, Ti–28Nb–10Ta–5Zr–0.3O and Ti–29Nb–10Ta–5Zr–0.3O alloys are fabricated by powder metallurgy processing, in which it undergoes severe deformation during swaging. Changes in the deformation behaviors of these alloys caused by small changes in the O and Nb contents are investigated in this study. The stress–strain curve of TNTZO changes nonlinearly with the strain and is characterized by a small stress hysteresis, indicating that TNTZO shows a nonlinear recovery behavior during unloading. This deformation in the alloy is a result of a typical elastic deformation as well as stress-induced martensitic transformation. However, with an increase in the O content, as in the case of alloys with 0.5O and 0.6O, the stress–strain curves change almost linearly with the strain and exhibit a linear recovery behavior during unloading without stress hysteresis. In such alloys, deformation is mainly caused by the typical elastic deformation. On the other hand, with a decrease in the Nb content, the stress–strain curves show two steps with an increase in the strain, and deformation is accompanied by stress hysteresis during both loading and unloading. This deformation is mainly caused by stress-induced martensitic transformation and reverse transformation.

ブックマーク

SNSによる共有

論文タイトル

生体用Ti–Nb–Ta–Zr–O系合金のミクロ組織と力学的機能性に及ぼすニオブおよび酸素量の影響

この機能はログイン後に利用できます。
下のボタンをクリックしてください。

詳細検索

論文タイトル

著者

抄録

ジャーナル名

出版日を西暦で入力してください(4桁の数字)。

検索したいキーワードを入力して下さい