Steel Science Portal

Kou kouzou rombunshuu
New Arrival Alert : OFF

You can use this feature after you logged into the site.
Please click the button below.

Log in / Sign up
ONLINE ISSN: 1884-0329
PRINT ISSN: 1880-9928

Kou kouzou rombunshuu Vol. 10 (2003), No. 39

  • Experimental study on the transferred friction force in the front side of bolt hole with high strength bolted friction joints

    Keiji HIRAI, Nobuyoshi UNO

    pp. 1-10

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_1

    Abstract

    In this paper, the results of slip tests on high strength bolted joints with normal 0.45 slip coefficient are herein. And the quantity of transferred friction force between a member and splice plate in the front side of bolt hole is considered from the results. From the consideration, it is clarified that on the average the transferred friction force in the front side of bolt hole is 36% of the design slip strength on a high strength bolt.

  • Elasto-Plastic Behaviour of High Strength Bolted Friction Joints

    Takuro EMI, Mototsugu TABUCHI, Tsuyoshi TANAKA, Hisashi NAMBA, Yoji NAGATANI

    pp. 11-22

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_11

    Abstract

    This study is planed to clear the behaviour of friction joints with high strength bolts on web bolted flange welded (WBFW) connections. In this study, web bolted connnection with high-strength bolts (WB) is tested. FEA is carried out and compared with the test result for considering the correctness of PEA procedure. The results are briefly shown: FEA result shows good correspondence with the test elasto-plastic behaviour of the friction joints. After the bolts contact with the plate, load which born by friction part decreased and the bearing load of the bolts increased.

  • A Study on Corrosion Prevention Paste of Suspension Bridge Cable

    Keita SUZUMURA, Shun-ichi NAKAMURA, Yoshifumi SAKAMOTO

    pp. 23-30

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_23

    Abstract

    Corrosion prevention properties of cable pastes (red lead paste, calcium plumbate paste and aluminium phosphate paste) are investigated. Moisture permeability of the pastes is two-hundredth of that with no paste. The effects of these pastes on galvanized wire are compared by salt spray test and immersion test contacting with degradation paste. Aluminium phosphate paste has good corrosion control, but red lead paste and calcium plumbate paste are not good with metal lead in the corrosion product. Inhibitor of paste-components affects corrosion prevention ability, and those with neutral property and without electrical positive metal such as lead are better.

  • Corrosion Prevention of Suspension Bridge Cables by S-shaped Wire Wrapping System

    Keita SUZUMURA, Tatsuya EGUCHI, Yoshifumi SAKAMOTO, Shun-ichi NAKAMURA

    pp. 31-38

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_31

    Abstract

    A new corrosion prevention system has been developed S-shaped wire wrapping with elastic type heavy duty coating (epoxy resin primer and fluorine top coats). The system intercepts corrosion factors such as water into the cable. S-shaped wire wrapping has better waterproof than general galvanized wires with a circle cross section. Elastic type heavy duty coating has good adhesive on new galvanized surfaces and has high corrosion prevention property, which was confirmed by weatherproof corrosion tests and immersion tests. It is shown by freeze-thaw cycle tests with small-sized cable specimens that the system prevents cracks even when the cable moves longitudinally.

  • Flexural Behavior and Hysteretic Characteristics of Exposed-type Column Base Subjected to Variable Axial Force

    Hidenori TANAKA, Yasuhiko KAMEMOTO, Isao MITANI, Takashi FUJINAGA, Michio ITOH

    pp. 39-49

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_39

    Abstract

    Two series test of the exposed-type column base were carried out to discuss relation of bending moment-rotation curve under variable axial force. One is subjected to axial load proportional to horizontal force and the other is proportional to beam shear force. The unbonded type anchor bolts are used for all specimens. Based on the test results, secant rigidity in elastic region of the anchor bolts and ultimate strength after yielding of anchor bolts are discussed. Finally model of bending moment-rotation curve is proposed.

  • A Study on the Stability of Circular Section Steel Stub-columns i n the Plastic-flow Range ‹D i screpancy Between Theory and Experimental Result for Elephant-foot Buckling›

    Tetsuro INOUE, Yoichi NAKAMURA

    pp. 51-61

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_51

    Abstract

    Maximum stress obtained by compression test of circular steel stub-columns were compared with deformation theory and incremental stress-strain theory. Each buckling analysis has a term of tangent modules Et in its solution. Therefore these solutions mean that all specimens buckle in the plastic-flow range before strain-hardening regionregardless of its diameter-to-thickness ratio. In spite of these theories, it is shown that specimens with small diameter-to-thickness ratio can be compressed into the strain-hardening range. Furthermore the efficiency of endurance of compressive force is referred between box-section and circular section steel stub-columns.

  • A study on new type of upper-deck steel arch bridges with superior seismic performance

    Tetsuya Nonaka, Tsutomu Usami, Katsumi Ogawa, Hiroshi Mitsuda, Maki Iwamura

    pp. 63-76

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_63

    Abstract

    The behavior of upper-deck steel arch bridges in severe earthquakes is quite complex and dynamic analysis is usually necessary for seismic designs or retrofits. By involving some recent advances in seismic design of steel piers, this study proposes a new type of such bridge structures with better seismic performance and lower cost, based on dynamic analysis results using elaborate models to account for the arch ribs and stiffening girders. In this proposed structural type, box section is adopted for all members of the bridge to employ the advanced seismic design techniques developed for box-sectioned steel piers. Moreover, to lower the cost, the proposed structure type is exempt from using the isolation bearings or dampers.

  • Earthquake Responses of Steel Frame Structures having a Structural Control System using Non-Structural Members

    Takashi TAGUCHI, Seishi YAMADA

    pp. 77-88

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_77

    Abstract

    Many structural control systems have been demonstrated to reduce the response during an earthquake and have gradually been applied to buildings. However, almost all the systems have required closure of the inter-column opening in order to install the damping devices. The authors have proposed a structural control system using non-structural members for steel buildings. This system is composed of non-structural members, which are short span beams. These members as hysteretis dampers absorb vibrational energy by their hysteretic damping performance. In this paper, the earthquake response analysis of the steel building has been carried out in order to under stand the behavior of the proposed system. As the result, the usefulness of the system has been discussed.

  • Plastic Deformation of Beams in Steel Moment Frames Subjected to Strong Earthquakes ( Part 1: Maximum deformation)

    Koji OGAWA, Hiroaki NAKAHARA

    pp. 89-104

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_89

    Abstract

    This study is concerned with the demand for ductility of beams in steel moment frames. Numerical response analysis was carried out for 15 frames against a variety of ground motions. This paper (Part 1) describes the magnitude of plastic deformation introduced into beam-ends. Maximum plastic rotation, maximum increment of plastic rotation during a half cycle of vibration, and the range of variable plastic rotation are considered as the parameters that represent the magnitude of plastic deformation. The results are summarized as formulas to predict those parameters based on maximum story drift angles.

  • Plastic Deformation of Beams in Steel Moment Frames Subjected to Strong Earthquakes ( Part 2 : Hysteretic behavior)

    Koji OGAWA, Hiroaki NAKAHARA

    pp. 105-120

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_105

    Abstract

    The previous paper (Part 1) described the magnitude of plastic deformation introduced into beam-ends. In this paper (Part 2), based on the same numerical results, we deal with hysteretic behavior. Cumulative plastic rotation, the increment of plastic rotation during each half cycle of vibration, and the hysteretic process of plastic rotation are discussed. A method is proposed to approximate damage to the beams in steel moment frames subjected to strong ground motions.

  • The Research about The Welding Defects and Repairs of Welded-joints in Steel Structure Buildings

    Eiji KITAMURA, Teruhisa KOUDA, Hiroyuki HAMADA, Hajime OGATA, Masanori MORI, Kazunobu YOKOTA, Tetsuya FUJITA, Kanji ISHIHARA, Iwao TSUYAMA

    pp. 121-129

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_121

    Abstract

    The Building Standard Law was revised and the notification No. 1464 was enacted. The permissible value over manufacture accuracy or a surface defect is specified for performance reservation of the welding joint, and when the fault exceeding occured, the reinforcement and repair which ensure the performance demanded by design should be carried out. The defective evaluation method of a welding part, and the reinforcement and the repair method are examined by AW official approval conference. It will the result investigated about the actual condition of the repair method from the questionnaire to a steel fabricater.

  • Verification to the breakage of center stay rod of the first Kurushimakaikyo bridge and field observation in the Geiyo earthquake

    Kazuhiko FURUYA, Hiroshi ISOE, Hiroaki HOASHI, Shigeru HIRANO

    pp. 131-141

    Bookmark

    You can use this feature after you logged into the site.
    Please click the button below.

    Log in / Sign Up

    DOI:10.11273/jssc1994.10.39_131

    Abstract

    Due to the Geiyo Earthquake in March 24th, 2001, center stay rods of the 1st Kurushimakaikyo Bridge(suspension bridge) were broken. They were designed to break in strong earthquake and work as safety valve of the structure. In order to evaluate the mechanism of the breakage of the rods, data from field measurement were processed using structural analysis, and it was confirmed that the broken rods worked as designed. It also was confirmed that forces acted to other unbroken rods in 2nd and 3rd Kurushimakaikyo Bridges were not large enough to affect their soundness. Through this experience, it was proven that field measurements and structural analysis can be effective tools not only for design but also for maintenance of structures.
  • © 2003 Japanese Society of Steel Construction

Article Access Ranking

16 Oct. (Last 30 Days)

  1. Preface to the Special Topics on “Cutting-edge Technologies and Scientific Researches of Zinc and Zinc Alloy Coated Steel Sheets” ISIJ International Vol.58(2018), No.9
  2. Mechanical Property of Ultrafine Elongated Grain Structure Steel Processed by Warm Tempforming and Its Application to Ultra-High-Strength Bolt Tetsu-to-Hagané Advance Publication
  3. Improvement of Wettability between Steel and Liquid Zn–Al Alloy by Forced Wetting ISIJ International Vol.58(2018), No.9
  4. Automotive Corrosion and Accelerated Corrosion Tests for Zinc Coated Steels ISIJ International Vol.58(2018), No.9
  5. Effect of Annealing Temperature on the Selective Oxidation and Reactive Wetting of a 0.1C-6Mn-2Si Advanced High Strength Steel During Continuous Galvanizing Heat Treatments ISIJ International Vol.58(2018), No.9
  6. Effect of Si/Mn Ratio on Galvannealing Behavior of Si-added Steel ISIJ International Vol.58(2018), No.9
  7. Crystal Structures and Mechanical Properties of Fe–Zn Intermetallic Compounds Formed in the Coating Layer of Galvannealed Steels ISIJ International Vol.58(2018), No.9
  8. Micro-Vickers Hardness of Intermetallic Compounds in the Zn-rich Portion of Zn–Fe Binary System ISIJ International Vol.58(2018), No.9
  9. Influence of Annealing Temperature and Dew Point on Kinetics of Mn External Oxidation ISIJ International Vol.58(2018), No.9
  10. Fracture Toughness of the Fe–Zn Intermetallic Compounds Measured by Bend Testing of Chevron-Notched Single-Crystal Microbeams ISIJ International Vol.58(2018), No.9

Search Phrase Ranking

16 Oct. (Last 30 Days)

  1. blast furnace
  2. blast furnace permeability
  3. blast furnace productivity
  4. isij international
  5. 半田恒久
  6. isij
  7. local formability high strength steel
  8. carbon monoxide reduction and accompanying swelling of lron oxide compacts
  9. castrip process
  10. convertor scrap